Caboolture South, QLD (display); factory Emu Plains, NSWPAAL Kit Homes
- Good for: Owner builders who want a full kit with published prices
- Good for: Rural and regional blocks anywhere in Australia
PAAL Kit Homes supplies complete steel-framed kit homes to owner builders, with a Queensland display home and showroom on Morayfield Road at Caboolture South. The family company says it was founded in 1970 and has produced more than six thousand homes, delivered to sites across Australia, with a particular focus on regional and rural blocks. Wall frames and roof trusses are roll-formed from BlueScope steel at its Emu Plains factory in New South Wales and arrive numbered and preassembled, backed by an owner's manual written for each home. A kit is delivered in three stages and covers council plans, framing, roofing, cladding, windows, insulation, linings, doors, kitchen, tiles allowance and fittings. The slab or floor, wiring, plumbing pipes and trade labour sit outside the kit. All 22 designs carry a published price including GST, and the Stanthorpe can be inspected at Caboolture.
- Display home and showroom at 67 Morayfield Rd, Caboolture South QLD
- Prices for every design published, including GST (ex factory, N3 wind rating)
- Steel frames roll-formed from BlueScope steel at its own Emu Plains factory
- Owner-builder kit delivered in three stages with a customised instruction manual
- Says it was founded in 1970 and has produced over six thousand homes
Visit PAAL Kit HomesSee their 8 homesThe straight answerCheck your block and place a home on it
Track record
| Install | Doesn't install. See the install builders |
|---|
| Business | PAAL HOMES PTY. LIMITED, ABN 56 075 266 027 |
|---|
| Trading | ABN registered 9 Mar 2000; the maker says The company was founded in 1970, and for over 55 years has continuously served the needs of Owner-Builders throughout Australia and abroad. |
|---|
Researched 15 Oct 2026 from PAAL Kit Homes' own site and the public registers.
Who they are
PAAL Kit Homes supplies steel-framed kit homes to owner builders and says it was founded in 1970. The company, PAAL Homes Pty Limited, has held its ABN since 2000 and roll-forms its frames at Emu Plains in NSW. It has a Queensland display home and showroom on Morayfield Road at Caboolture South.
What they make
Twenty-two designs, mostly full-size three to five bedroom homes from 141 to 240 square metres under roof. Frames and trusses are high-tensile steel, numbered and preassembled, with Hardiplank or Newport cladding. Designs can be extended or changed.
What the price covers
Every design carries a published kit price including GST, from $148,200 for the Blackheath to $196,010 for the Robertson among the eight lowest. Prices are ex factory; delivery is charged by site. The slab, wiring, plumbing pipes and all labour are outside the kit.
Installing one in Queensland
PAAL does not build. The buyer builds under an owner builder permit or hires a licensed builder, and PAAL can refer builders in some areas. Approval runs through the buyer's certifier using PAAL's plans.
Who it suits
Owner builders on larger or rural blocks who want a full-size steel-framed house kit at a published price.
Worth checking
These are mostly full-size houses, not compact secondary dwellings, so check the floor area against your council's secondary dwelling limits. No warranty term is published.
No maker pays to be listed or ranked, and every list is sorted by price, never by who pays. This isn't every maker in the market yet: missing one? Say which. Prices and sizes are the makers' own, read from their websites on the date shown, and makers change them: check with the maker before you buy. Installed prices are estimates for an owner builder, inc GST, from the install cost calculator; a licensed builder adds about $10,000. Is a listing yours, or wrong? Claim it, fix it or have it taken down.
